Recent Posts

1

Technical / ESA Module replaced - VIN mismatch

« Last post by MCMXCIVRS on Today at 12:48:21 AM »

I had issues with my ESA on my 2019 F850GSA recently and the solution was to replace the control module as there was no way I could correct the problem with the original one. There was a calibration fault code that would not clear, all other components of the system tested OK. I was able to source a used module and with it installed the system functions normally again and no codes are present, however when I scan the bike the GS911 shows a message indicating the VIN for the ESA module is mismatched which is not surprising. What I'd like to know is, can this be reprogrammed with the GS911 to correct the VIN or is that a dealer only function if possible at all?

2

GS-911 / Re: Calibration Error - Why?

« Last post by Adam westerman on November 30, 2024, 08:33:00 PM »

Hi, I am ex bmw tech were i used to work went into administration but seen your post and weirdly the bmw diagnostics would fail calibration on the new fuel file strips and we asked bmw technical and they said yeah normal try up to 30 to 40 times and see what happens, after that try another file strip so maybe you need to try a few more times, but also a massive thing is making sure the voltage is correct you could almost do with it being at running voltage around 14volts this was also a factor we had to do at the bmw dealership
Not sure how much of that will be helpful
Thanks
Adam

3

Technical / Re: datalog sampling frequency

« Last post by WayneC on November 30, 2024, 12:51:47 PM »

OK good to hear, with your original logging I am unsure how you had the GS911 connected

With a PC vIa USB data throughput on USB2 can be a limitation, you can set communication with PC to be TCP-IP to then to WiFi via home router & you may find improved logging rates. Used in workshops to have wire free diagnostics

4

Technical / Re: datalog sampling frequency

« Last post by the_grizzli on November 30, 2024, 11:29:28 AM »

it's ok for the acquisition via wifi on the SD card.

the frequency seems to be faster and 6 values ​​out of 9 are on the same timeline.
the offset between two values ​​is 380ms

On a graph, We can clearly see the offset of the high point of the accelerator handle, offset from the high point of rpm

5

GS-911 / Re: anyone familiar with this code? 0x3A1122 Thanks!

« Last post by Thealmightyhabibi on November 30, 2024, 07:15:19 AM »

Problem solved… checked each coil pack individually until code popped up. Swapped coil pack, replugged all wires back cleared all codes and turned the bike on with no faults.

6

GS-911 / Re: Configuring wifi manually won't save

« Last post by WayneC on November 30, 2024, 04:17:59 AM »

I looked at the IOS hot spot set up a while back & found it confusing, are you referring to the OS on the iPhone being up to date or the GS911 WiFi firmware being up to date ?

You may be best lodging a support ticket with HexCode https://www.hexgs911.com/contact-us/

7

GS-911 Wifi / Re: New December software/firmware with no info ?

« Last post by GwenSimmons on November 29, 2024, 09:47:10 PM »

another one that can't follow the news

https://www.hexgs911.com/news/april-2024-software-and-firmware-updates/

aftermarket tools that to allow you to save thousands outside the deliberately corrupt and incompetent rip off dealer networks of all manus, are by small start up companies with limited budgets
that's the whole point - they are not massive corporate crooks trying to implode the entire world in on itself for a few miniblox elites to manage your lives in to a jail cell (of a netflix supplied living room). 

Thus their marketing and info services are not so evolved - if you want corporate slime and a "free coffee" pay $200 to hear lies at you local motorrad theft shop

Thanks.

8

GS-911 / Configuring wifi manually won't save

« Last post by pedroridesagain on November 29, 2024, 04:52:44 PM »

Hi,

I am having the most difficult time configuring my wifi to work with phone's hot spot (iPhone), up to date OS. Bike battery is new and charged. I follow the instructions here: https://www.youtube.com/watch?v=NwJCOrqN21s step by step. When I hit save, the SSID field and the password field go blank and it will not connect in infrastructure mode.

Has this happened to anyone else?

9

Technical / Re: datalog sampling frequency

« Last post by WayneC on November 29, 2024, 10:39:14 AM »

thanks for the details.
i actually connect with my phone's app in D2D.
however, i don't think i saw an option to connect "directly" to the SD card...
did i miss something?

The setting to log to SD card is in the real time logging screen when you are setting the parameters to log

10

Technical / Re: datalog sampling frequency

« Last post by the_grizzli on November 29, 2024, 10:23:41 AM »

thanks for the details.
i actually connect with my phone's app in D2D.
however, i don't think i saw an option to connect "directly" to the SD card...
did i miss something?