Recent Posts

Pages: [1] 2 3 ... 10
1
R1250 models / Re: List of all monitored sensors
« Last post by Mats@MFT on Today at 04:52:36 PM »
Have you seen the ezCAN accessory manager already? https://www.hexinnovate.com/hex-ezcan-for-bmw/
This should be an ideal and safe solution to distribute your bikes energy
2
R1250 models / Re: List of all monitored sensors
« Last post by schuppi on Today at 09:28:47 AM »
This measured value cannot be read out with the diagnostic device.
In order to be able to measure this value, an ampere meter must be connected.
3
R1250 models / List of all monitored sensors
« Last post by Memphomaniac on Today at 04:22:36 AM »
Is there a list of all monitored sensor values somewhere? I am specifically looking for electrical system amperage. I plan to add some high current draw devices to the bike, and I need to see how much current the bike is presently using. I know the bike comes with a 510W alternator, which at 14V, results in ~36A. I am planning to add 2 13A draw devices (26A total), each connected to the PDM60 15A feed circuits, but I need to know how much of the 36A the bike uses before I add these devices. Using 26A only leaves 10A for the rest of the bike.
4
GS-911 / Re: Gs 911 USB (blue)
« Last post by mike d on July 26, 2021, 10:55:27 AM »
I still have an old GS-911 USB (Blue), in fact it was used recently. If you download the Downloader Utility, then you can follow that with the installation software (I use the Windows version on a laptop).

Mike
5
Hello. I also have such a problem, an error on the ABS sensor. I made an adapter, the native software cannot connect to the processor, but the processor responds to the R, S and T symbols in the terminal.
The data flow is very similar to the post above.
Has anyone understood or deciphered what this data means? And how do you adjust the coefficients?
6
How do I... / Wifi help please
« Last post by Bobby on July 26, 2021, 09:12:10 AM »
Hello people, could someone write a complete dummy guide to connecting my I phone to my hex code 911 and the wifi, I seem to just go round in circles, It works with a USB cable to my Mac but I am unable to connect my hex code and my I phone to the same wifi and access the service functions
I have watched the tutorial but it doesn't seem to help.
7
GS-911 / Gs 911 USB (blue)
« Last post by Virginiapi on July 25, 2021, 11:47:34 PM »
I just purchased the above unit to use on my 2009 K1200LT, my buddies 1999 K1200LT and his R1100R. I can't seem to be able to find the downloads for this device. Are they still availible? Can it be used on an Andriod phone? Any suggestions or help appreciated.
Bill
8
Thanks for this finding DR, I will be lengthening my "highway" count also, oftentimes it's just a bit too short when you can't just move right over.
9
they seem to do a time and distance thing

33 flashes round town and 17 at higher motorway speeds (on both the GS or the K1300)

trouble with shortening 17 is too little on big European motorway junctions....  19 would have been just enough, 20 far safer
its more a kill in case u forgot than something you are supposed to use....
10
Technical / Re: New GS-911 w/ latest software can't read OBDII
« Last post by Mats@MFT on July 22, 2021, 02:54:37 PM »
GS-911wifi with OBD-II connector but there shouldn´t be any differences with 10pin and adapter
Pages: [1] 2 3 ... 10