Author Topic: Hello from Northern Colorado  (Read 11595 times)

twmichels

  • Newbie
  • *
  • Posts: 8
  • Karma: +0/-0
Hello from Northern Colorado
« on: May 28, 2019, 01:28:23 AM »
Hi, just purchased GS-911 for 06 R1200RT

WayneC

  • Beta testers
  • Hero Member
  • *
  • Posts: 1503
  • Karma: +34/-1
Re: Hello from Northern Colorado
« Reply #1 on: May 28, 2019, 02:50:38 AM »
Welcome to the forum, plenty of people to assist as you get used to using the GS911

twmichels

  • Newbie
  • *
  • Posts: 8
  • Karma: +0/-0
new user, O2 sensor question code 10010
« Reply #2 on: May 29, 2019, 04:59:21 AM »
Hi,  just hooked up GS-911 to '06 R1200RT.
Symptoms rough idle, will not idle without throttle , Error Code: 
BMS-K
10010: Lambda (O2) sensor (Cylinder 1)
The fault is currently present.
This fault occurred 2 times.
Logistic counter: 40
Symptom: Signal or value over threshold.
MIL set: No
Fault code history:
Engine speed
1840.00 rpm.

switched o2 sensors, no change in running poorly, same graph results on the cylinder 1 graph flatline.

Any suggestions, also temp is 20% lower  on right cylinder?  Thanks!

TW

Any suggestions



schuppi

  • Hero Member
  • *****
  • Posts: 558
  • Karma: +21/-0
Re: Hello from Northern Colorado
« Reply #3 on: May 29, 2019, 10:22:17 AM »
Hello and welcome

Ideas
Please check
Valves adjustment?
Measured values idling position 0 ° TPS functions
Throttle cables synchronously
Connections Ignition coils
pencil coils
Seals of the intake system
Schönen Tag
Wolfgang
                                       talk less, drive more

twmichels

  • Newbie
  • *
  • Posts: 8
  • Karma: +0/-0
Re: Hello from Northern Colorado
« Reply #4 on: May 29, 2019, 03:22:12 PM »
Hello and thank you,

Ideas
Please check
Valves adjustment? -      yes, less than 200 miles ago, 36K mi svc, used JVB excellent video
Measured values idling position 0 ° TPS functions -   does the GS-911 measure this ?
Throttle cables synchronously -   checked movement, seems to be moving ok
Connections Ignition coils-  cleaned connections and replaced plugs
pencil coils-   replaced both main coils ( the cylinder one coil  had broken in cylinder, discovered when removing plugs  )
Seals of the intake system -  not sure ?  tighten up boots?

Assistance is appreciated, I completed 36 k mi svc, valve adjust, plugs, replaced main coils, oil, transmission, final drive and ABS brake flush, I did not sync the throttle bodies ( fired up and sounded fine).
  Around a 150 miles  later, during a ride in mountain,s  accelerated up hill, power cut out(felt like out of gas ? ). Stopped, visual check, would not start with out throttle roll, would not exceed 40 mph returning home.  Throttle needed rolling during traffic stops.  Fuel had not been added, ie ran fine before.

Thanks!!! :)


TW

schuppi

  • Hero Member
  • *****
  • Posts: 558
  • Karma: +21/-0
Re: Hello from Northern Colorado
« Reply #5 on: May 29, 2019, 08:36:54 PM »
Measured values idling position 0 ° TPS functions -   does the GS-911 measure this ?

Hello
select engine choose real time values and log this data while engine is running.
In your case just with minimally open throttle (~1500rpm or less) for one minute.


Schönen Tag
Wolfgang
                                       talk less, drive more

twmichels

  • Newbie
  • *
  • Posts: 8
  • Karma: +0/-0
Re: Hello from Northern Colorado
« Reply #6 on: May 29, 2019, 09:54:25 PM »
Will do as suggested, later this evening, and advise results.  Thanks for your feedback :)

TW

twmichels

  • Newbie
  • *
  • Posts: 8
  • Karma: +0/-0
Re: Hello from Northern Colorado
« Reply #7 on: May 30, 2019, 05:02:32 AM »
Hi, ran the real time time values, PDF is attached with results. Much appreciation for assistance.  TW

schuppi

  • Hero Member
  • *****
  • Posts: 558
  • Karma: +21/-0
Re: Hello from Northern Colorado
« Reply #8 on: May 30, 2019, 08:32:41 PM »
Hello
There are no measurements on lambda 2. That's bad.
Think there is a malfunction with this sensor. I would test the connections of the left side lambda sensor.
Possibly swop the sensors and measure again.
Check if the error changed to the right side. Then replace this Lambda sensor
« Last Edit: May 30, 2019, 09:43:45 PM by schuppi »
Schönen Tag
Wolfgang
                                       talk less, drive more

twmichels

  • Newbie
  • *
  • Posts: 8
  • Karma: +0/-0
Re: Hello from Northern Colorado
« Reply #9 on: May 30, 2019, 09:46:26 PM »
Thank you, that makes sense , will try swapping O2 sensors and re-check results for the non voltage. will advise, thanks! //TW

schuppi

  • Hero Member
  • *****
  • Posts: 558
  • Karma: +21/-0
Re: Hello from Northern Colorado
« Reply #10 on: July 26, 2019, 10:47:16 PM »
Hi  Jackarce

copy an entry to insert stupid links.
get your little shovels and please play in another sandbox.
Schönen Tag
Wolfgang
                                       talk less, drive more

twmichels

  • Newbie
  • *
  • Posts: 8
  • Karma: +0/-0
Re: Hello from Northern Colorado
« Reply #11 on: August 04, 2019, 01:11:26 AM »
apologies

twmichels

  • Newbie
  • *
  • Posts: 8
  • Karma: +0/-0
Re: Hello from Northern Colorado
« Reply #12 on: August 04, 2019, 01:16:36 AM »
Apologies, valve broke, replaced piston, bore, valve head.  Thanks for quick responses sir!    TW

schuppi

  • Hero Member
  • *****
  • Posts: 558
  • Karma: +21/-0
Re: Hello from Northern Colorado
« Reply #13 on: August 04, 2019, 05:41:58 PM »
Hello,

Thanks for the feedback.
Good ride and many beautiful miles with your repaired RT
Schönen Tag
Wolfgang
                                       talk less, drive more