Author Topic: ESA Rear rebound adjustment, open-circuit  (Read 607 times)

Dill

  • Newbie
  • *
  • Posts: 3
  • Karma: +0/-0
ESA Rear rebound adjustment, open-circuit
« on: December 27, 2018, 02:46:57 PM »
Hi Guys I serviced my 2010 RT yesterday and carried out an Autoscan before I started. I noticed a fault in the ZFE. No warning lights on 
41775
Rear rebound adjustment, open-circuit
The fault is currently present.

I cleared the fault and carried out a Rear ESA calibration and came back with successfull. I had two pids to calibrate the front and the rear, when attempting to do the front it came back with a error "Negative Response received from controller, conditions not correct or incorrect sequence of commands" But when I thought about it theres no motor on the front shocker so I guess this error was expected.

I am going to check the plugs for corrosion etc, but just wondered if this a common problem and what the fix is for this fault.
I enclose my Autoscan and many thanks in advance for any advise.

AutoScan Report
GS-911 version: 1812.1 Datapack version: 11.1
Serial Number: GS1 012 760
Firmware version: 0.254-0.161 Datapack version: 0.144
Registered to: Keith Simpson
Date: 26/12/2018 Time: 13:02:16
Motorcycle Information
VIN: WB1043007AZW30940
Mileage: 30204.4 miles
Cluster date: 27 December 2018
Next service date: 26 December 2019
Next service distance: 36205 miles
Factory I-Level: K024-09-08-560
Actual I-Level: K024-17-07-500
BMS-KP2
BMS type: BMS-KP2
Controller Type: Engine Controller
Part No.: 8521661
Hardware Index: C6
Coding Index: 03
Manufacture Date (YY/MM/DD): 2010-01-12
MCV: 0.6.2
FSV: 0.77.51
OSV: 2.3.1
Manufacturer: Bosch GmbH
HWOE No.: 68189264
Program status: 510I
Date release: XA11
Factory I-Level: K024-09-08-560
Actual I-Level: K024-17-07-500
VIN model year: 2010

No fault codes found

ZFE-High
ZFE type: ZFE-High
Controller Type: Vehicle Electronics
Part No.: 8394896
1 of 3 26/12/2018, 13:35
Hardware Index: 08
Coding Index: 30
Manufacture Date (YY/MM/DD): 2004-04-15
MCV: 0.6.4
FSV: 3.7.0
OSV: 3.3.0
Manufacturer: Loewe / Lear
HWOE No.: 67167736
Factory I-Level: K024-09-08-560
Actual I-Level: K024-17-07-500
Speed sensor manufacturer is Bosch
Speed sensor type is DF11
ABS fitted
ESA fitted
ESA has hall sensor
Heated grips
Heated seat driver
Heated seat passenger
Push button heat
Outside temperature sensor
Brake light switch status over CAN
Film type fuel sensor
Manual low beam off switch
Increased power output for high beam
Electronic windscreen present
Cruise control present

1 fault codes found:
41775
Rear rebound adjustment, open-circuit
The fault is currently present.

Integral ABS 2 - CAN
Controller Type: ABS Brakes
Part No.: 7711978
HW Version No.: C2
Coding Index: 0
Manufacturing Date: 2009-12-17
HWOE No.: 61687592
Manufacturer: Continental Teves
MCV: 0.6.0
2 of 3 26/12/2018, 13:35
FSV: 2.2.0
OSV: 3.3.0
Free programming slots: 1
Serial No.: 69CH00250
Hardware No.: 07682002
Hardware star No.: 07711978
No fault codes found
CAN-Kombi H/L
Cluster type: CAN-Kombi H/L
Controller Type: Instrument Cluster
Part No.: 8520039
Hardware Index: C8
Coding Index: 07
Manufacturer: Siemens VDO Automotive
Manufacture Date (YY/MM/DD): 2008-11-27
MCV: 0.6.3
FSV: 2.3.0
OSV: 3.3.10
HWOE No.: 68168448
Assembly No.: 8520040
Variant: K26
Factory I-Level: K024-09-08-560
Actual I-Level: K024-17-07-500

No fault codes found

« Last Edit: December 27, 2018, 02:51:14 PM by Dill »