Recent Posts

Pages: [1] 2 3 ... 10
1
General Discussion / Re: Very crazy idea
« Last post by WayneC on May 24, 2022, 04:04:56 AM »
Have a crazy idea, and need some advise in this regards.

Is it possible to male GS911 act as an interphase for IstaP?

Regards
Ray

No
2
GS-911 / Re: ABS light is on and GS-911 scan shows no error
« Last post by MudBug on May 24, 2022, 12:11:40 AM »
:D  That was it.  It was stuck on.  I held down the ABS long enough that it started flashing, turned the key off, started the bike and road it.  All normal now.  I am new to BMW, so this is new to me.

Thanks! 
3
General Discussion / Very crazy idea
« Last post by exopar on May 23, 2022, 10:29:48 PM »
Have a crazy idea, and need some advise in this regards.

Is it possible to male GS911 act as an interphase for IstaP?

Regards
Ray
4
ezCAN / ezcan Gen 1 for sale
« Last post by Allen on May 23, 2022, 05:55:53 PM »
Hi , I have a never used gen1 ezCan made for BMW 1200 -1250 LC , all pieces as came in packaging . offers ?
5
ABS related issues / Re: Servo activates when connected to GS 911?
« Last post by JayGS on May 22, 2022, 09:44:09 PM »
I took apart the ABS module last night. It was pretty clean on the inside for the most part. all the internal o-rings and filters were were in good shape. The only part I didn't tamper with were the motors at the base of the module because I believe those are part of the control circuit and that system is showing no faults. I sprayed the crap out of the pressure sensor for the wheel circuit with electric cleaner and compressed air. The sensor itself did have some gunk on it on one corner that had hardened and appeared to bridge the small space between the pressure plate and the housing. I was hopeful that was the problem since I didn't find any other potential problems. The passage to the sensor was unobstructed and cleaned.

I put it all back together today and still showing high pressure(120 bar) in the front wheel circuit!! I guess it has to be a faulty sensor. Anything else I should try before gambling on a used ABS unit if I can find one?
6
Biker's Pub / High energy coffe cup
« Last post by exopar on May 22, 2022, 08:35:27 PM »
Here how to make a high energy coffe cup.
https://youtube.com/shorts/XD-0HrYF6CY

Regards
Ray
7
General Discussion / Re: Purchased a f800gs at salvage
« Last post by exopar on May 22, 2022, 08:14:21 PM »
 >:( >:( >:(
8
ABS related issues / Re: Servo activates when connected to GS 911?
« Last post by Jughead on May 22, 2022, 02:02:04 PM »
Yes, the pressure sensors are on the ABS pump.  The control circuit sensors are inside the pump (behind the controller) while the wheel circuit sensors are on the outside on the left end of the pump as view from the seated position.

Both front and rear control circuit sensors are on the same module (you cannot separate them) and the wheel circuit sensors are on the same module.

Checking the Realtime Values, the pressure of all four sensors should be somewhere between 18 and 24bar.
9
General Discussion / Re: Purchased a f800gs at salvage
« Last post by Jughead on May 22, 2022, 01:52:13 PM »
No.  That would require a visit to your local friendly BMW dealer.
10
GS-911 / Re: ABS light is on and GS-911 scan shows no error
« Last post by Jughead on May 22, 2022, 01:50:37 PM »
It is possible that your ABS is stuck in the OFF mode.

What mode is the bike in?  In Enduro Pro mode the ABS is turned off on the rear, but that shouldn't turn the light on.

What happens when you press and hold the ABS button?  Does the status of the light change at all?
Pages: [1] 2 3 ... 10