GS-911 and ezCAN User Forum
General Category => Technical => GS-911 => ABS related issues => Topic started by: guysat on March 26, 2015, 12:31:24 AM
-
Hi all
Just purchased a GS-911 WiFi to help me sort out the flashing ABS lights.
Great bit of Kit, really please with it, worth every penny, professional piece of Kit
The Bike is a 2000 K1200RS (UK) Have connected to bike and can read the Engine Module OK, but the ABS module can not be found :-\
Have checked pins 14 & 15 to ensure the ABS module has power and it has.
Does this mean the ABS module has failed and not a mechanical pump problem, any thoughts on this would be gratefully received.
AutoScan : -
Base System Version : 0.215 - 0.111
Serial Number : GS1 001 686
Registration : Guy Satterthwaite
Date : 2015-03-25 19:10:58
- :
Motronic MA2.4 : -
Controller Name : Motronic MA2.4
Variant : K1200 RS 96kW N1050
Part No. : 7655477
Bosch part number : 0261204314
ECU Software number : 1037352655
ECU coding variant : 0
ECU program version : 10040400
Manufacturer : Bosch
Idle Actuator present : YES
Lambda control : Lambda control
Fault Codes : 0
No Faults found :
-
Hi all again.
Today I have done the pin 2 & 21 to ground trick to reset ABS module. To my great surprise it worked, quick test drive and lights stayed out :D
But the GS-911 still does not communicate with the ABS module (Engine OK), have checked cable/pin-20 to diagnostics plug and OK
I believe this is the ABSII version and that the GS-911 supports communicate with that model....?
Is there another reason the GS-911 will not communicate....?
Guy
-
Not certain why any of those who know your model better have not responded but if the GS911 has not recognised the ABS I would lodge a support ticket with Hexcode as it should be seeing it, it is usually better at seeing the ABS when BMW diags at times will not
-
You didn't say if you were using the PC app or not. The note on the http://www.hexcode.co.za/products/gs-911/function-chart page says:
ABS-II : Also known as ABS-2 - the predecessor to integral ABS (iABS, also known as servo assisted) on most R850, R1100, R1150 and older K1200 models. (*Due to protocol timing constraints, ABS-II is ONLY supported in the Windows versions of the software!)
Were you using the app or the built in functions of the wifi version?
-
Hi Marchyman
arh..... I have the GS-911 WiFi model and was using my iPad to connect.
I will have to borrow a PC laptop and have another go...
Will update
Regards
Guy
-
You didn't say if you were using the PC app or not. The note on the http://www.hexcode.co.za/products/gs-911/function-chart page says:
ABS-II : Also known as ABS-2 - the predecessor to integral ABS (iABS, also known as servo assisted) on most R850, R1100, R1150 and older K1200 models. (*Due to protocol timing constraints, ABS-II is ONLY supported in the Windows versions of the software!)
Were you using the app or the built in functions of the wifi version?
All sorted wish I had read that, ABS connected with no issues once using a PC... ::)
-
Well ABS lights have decieded to make a re-appearance, straight after I pulled out of a gritty lay-by and the rear wheel spun up a little on the gravel, (strange as this has no braking involved)
I updated the GS-911 unit before trying to connect with bike, then connected to bike and was able to reset fault codes using a 'Mac computer' and all is good again :D
Keep up the excellent work with this GS-911 unit :D
-
Did you read the fault code before clearing it?
Perhaps you have an underlying issue.
Mike