Recent Posts

Pages: [1] 2 3 ... 10
1
I’m sorry I didn’t state correctly what I was getting at. You have the option to add Connect Ride to the menu items on the TFT (My Vehicle, Navigation, Media, Telephone).

I see the Connected Ride when going through the menu option I see Connected Ride but there isn’t an option to select anything under that menu item even though my iPhone is connected to the TFT.

 
2
On my XR, the connectedride app fetches and makes available information like the speed limit for your current road.

My phone also records my rides, and available information from the motorcycle like speed, rpms, throttle, lean angle, G forces, etc..  Very nice for when I tag along on a fun route with someone -- I automatically record it. :)
3
Hello,

what exactly is ment by the following (that came as a feature with the october 2024 update):


"Enhanced Navigation: You can now enable your XKOMBIHI instrument cluster, to use the BMW Connected app."


I just saw that today. I don’t know how it works with the Connected Ride app on the iPhone. Have you figured out what you can do with it?

4
GS-911 / Re: reset service code
« Last post by walterhong1@gmail.com on Today at 07:32:08 PM »
Hi Jim,

I found it, finally.  I wasn't looking in the right area.  Thank you for the reply.

Best,
Walter
5
GS-911 / Re: reset service code
« Last post by GS Jim on Today at 05:06:07 PM »
I'm not sure what bike you have Walter as you don't say but after selecting your model go to Controllers and select the Instrument Cluster controller (Kombi) then select Service Functions and it should be under Offline Service Functions.
You may also find it under the list of controllers in a section called Service Reminder/Vehicle Functions and then select Offline Service Functions.
At least this is where it is on a 2018 R1200 GS.

.
6
GS-911 / USA Spec R1250GSA - MPH to KPH?
« Last post by Missin44 on Today at 12:34:30 AM »
I have a US spec R1250GSA. For whatever reason BMW made it that US bikes can not be switched between MPH to KPH. It's a PITA when crossing the boarder into Mexico or Canada.

Is it possible to add this function with the GS911? If so could someone to the link that describes the procedure?
7
GS-911 / Re: reset service code
« Last post by walterhong1@gmail.com on May 11, 2025, 10:56:01 PM »
I don't see "Special Functions" anywhere.  Can you help me locate it?
8
GS-911 / Re: How to Remove “Drive1” Warning Using GS-911
« Last post by WayneC on May 11, 2025, 02:23:29 AM »
Welcome to the forum

There should have been no difference in detection of fault codes between D2D & Infrastructure modes

I assume you registered the GS911, ensured firmware was updated to the latest & you dont mention whether you were using Browser or PC App to use the GS911

I would lodge a support ticket with Hexcode - https://www.hexgs911.com/contact-us/
9
Dear All,

For some reason I don't see a way to reset the service due message on my 2023 BMW s1000rr.

Can you help?

Best,
Walter
10
GS-911 / Re: How to Remove “Drive1” Warning Using GS-911
« Last post by Striff on May 10, 2025, 06:38:35 AM »
Update: No help from here, but I managed to sort it myself! 😄

Turns out, when I connected the GS-911 via D2D mode, it picked up the errors and let me clear them. When I was connected via Infrastructure mode, it didn’t show any errors at all — not sure if that’s by design or just a happy coincidence.

Anyway, consider this a PSA for anyone else facing the same issue. And thanks everyone for the overwhelming silence — I clearly had to experience the full “DIY adventure” spirit here! 😜
Pages: [1] 2 3 ... 10