GS-911 and ezCAN User Forum

General Category => ezCAN => Topic started by: motoUX on April 22, 2021, 05:29:07 PM

Title: Using ezCan Hex Gen II with Admore lights and TT Denali D2 aux lights & aux horn
Post by: motoUX on April 22, 2021, 05:29:07 PM
Hi all,

Here's what I would like to connect:
for a total of four circuits. It seems that, for my Admore light strip to work for both brake/running and turn signals, it needs two separate circuits. I'm fine with my D2 lights being on or off (rather than being controlled separately).

Is this possible? Thanks in advance!
Title: Re: Using ezCan Hex Gen II with Admore lights and TT Denali D2 aux lights and aux ho
Post by: StephanT on April 22, 2021, 06:16:33 PM
hi motoUX

not sure what the question is - you seem to have figured it out already...  ;D

What you should do is set one channel to (https://i.imgur.com/J8jJfXr.png)

Set another to (https://i.imgur.com/fPjPrFj.png)

and then the remaining two to (https://i.imgur.com/cB9Qsvl.png) and (https://i.imgur.com/ziC4TDc.png) respectively

to connect the lights to one circuit a splitter comes in handy: https://www.hexinnovate.com/product/mt-3-pin-y-splitter-cable/ (https://www.hexinnovate.com/product/mt-3-pin-y-splitter-cable/)
(https://i.imgur.com/t19F44U.jpg)

and you're good to go!  ....ez  ;D


Title: Re: Using ezCan Hex Gen II with Admore lights and TT Denali D2 aux lights and aux ho
Post by: motoUX on April 22, 2021, 08:49:46 PM
hi motoUX

not sure what the question is - you seem to have figured it out already...  ;D
....

to connect the lights to one circuit a splitter comes in handy: https://www.hexinnovate.com/product/mt-3-pin-y-splitter-cable/ (https://www.hexinnovate.com/product/mt-3-pin-y-splitter-cable/)
(https://i.imgur.com/t19F44U.jpg)

and you're good to go!  ....ez  ;D

Ah...might have to reattach the D2 connectors to I can use the splitter, I reckon (when the dealer installed the lights, they cut the Denali quick-connectors off in order to install the lights using posiconnectors on the EZHC)
Title: Re: Using ezCan Hex Gen II with Admore lights and TT Denali D2 aux lights & aux horn
Post by: motoUX on April 22, 2021, 10:52:11 PM
Aaaand....Y-cable is now ordered!
Title: Re: Using ezCan Hex Gen II with Admore lights and TT Denali D2 aux lights & aux horn
Post by: motoUX on June 07, 2021, 02:13:16 PM
Hooking the new unit up Wednesday...fingers crossed (or Daumen gedrückt, or whatever your symbol for "good luck" might be!).
Title: Re: Using ezCan Hex Gen II with Admore lights and TT Denali D2 aux lights & aux horn
Post by: motoUX on June 10, 2021, 02:03:27 PM
Received my new unit (thanks!). Now ready to install...and I still have a question ;)

If I use two circuits for the Admore lights (one left blinker and one right blinker), will i have

I'm only asking because, on the Web site, it has this info:

There are multiple ways of connecting your Admore light to the ezCAN. To make full use of the features of the Admore light connect the wires and configure the ezCAN as follows:

ezCAN accessory output (white) to Admore Red (switched 12V source)
ezCAN brake output (yellow) to Admore Blue (brake input)
ezCAN accessory or brake ground (black) to Admore Black (ground)
Admore green and yellow (right/left turn signal inputs) can be tapped directly into the turn signal wires of the bike, as per the Admore instructions
Configure the ezCAN to use 2 channels with the yellow and white configured for brake and accessory respectively, remember to set the tail/rear light brightness to 0% and the brake light brightness to 100%. Set the ezCAN brake to “No flashing”.


I prefer NOT to tap into existing wiring via splicing into the bike's turn signal wiring.

Make sense?  Thanks!
Title: Re: Using ezCan Hex Gen II with Admore lights and TT Denali D2 aux lights & aux horn
Post by: motoUX on June 12, 2021, 10:22:08 PM
Totally didn't work. Back to square one.
Title: Re: Using ezCan Hex Gen II with Admore lights and TT Denali D2 aux lights & aux horn
Post by: Ruan on September 09, 2021, 10:39:26 AM
Hi MotoUX

I've had a look through your thread and noticed some potential troubles you might run into.

Please let me know if you have any questions moving forward. For any support related queries you are also welcome to email our support helpdesk on support@hexezcan.com.

Kind regards
Ruan
Title: Re: Using ezCan Hex Gen II with Admore lights and TT Denali D2 aux lights & aux horn
Post by: StephanT on September 22, 2021, 07:24:35 PM
@MotoUK : are you up and running?  if not, talk to support and they can send you the configuration file for your setup... (let us know what you have connected to which output of the ezCAN (red, blue, yellow, white)

best
Stephan