General Category > Central Vehicle Electronics/ZFE/GM issues

K1200S will not recognize ESA calibration

<< < (2/3) > >>

ricknut:
Let me know if i can help.  :)

kobus:

--- Quote from: ricknut on June 03, 2013, 02:51:47 PM ---Yes, this bike does have the ESA. I heard the motors come on Friday night.  Maybe I am confused but bike does have an ESA button and lcd display does have normal, comfort and sport when I press esa button.

When I bought this bike used three years ago, the esa motor wires were for some reason clipped and I had an error code. I repaired wires and esa seems to work.  Not sure why the controller will not complete ESA calibration test.

--- End quote ---

The calibration test is only for ESA with Hall sensors. Your ZFE configuration says you do not have this type of ESA and thus it cannot be calibrated.
Some earlier ESA versions has resistive sensors and cannot be calibrated.


--- Quote from: ricknut on June 03, 2013, 02:51:47 PM ---I tried the other ZFE tests from new beta software and all seems fine but horn test. Horn test would turn on but not turn off so I had to turn off ignition switch.

--- End quote ---
Do you have an aftermarket horn fitted? If there is an error on the output it usually stays on - had the same issue during Beta testing with a fuel pump controller which caused the fuel pump to stay on.

rapala50:
I have a 2008 R1200rt with ESA and also had an error message saying No ESA can be calibrated is fitted for this motorcycle , I then ran a autoscan and the ZFE did not show the ESA , is this something Hexcode will be able to correct on bike that have different types of ZFE ?



 
VIN: WB10388088ZT12579
Mileage: 37417.0 km
Factory I-Level: K024-07-10-500
Actual I-Level: K024-09-02-500

--------------------------------------------------------------------------------
BMS-KP2BMS type: BMS-KP2
Part No.: 7722565
Hardware Index: 10
Coding Index: 2
Manufacturer: Bosch
Manufacturing Date: 2007-09-02
HWOE No.: 25923656
MCV: 0.6.0
FSV: 0.77.35
OSV: 2.3.1
Factory I-Level: K024-07-10-500
Actual I-Level: K024-09-02-500
VIN model year: 2008




No fault codes found

--------------------------------------------------------------------------------
ZFE-HighZFE type: ZFE-High
Factory I-Level: K024-07-10-500
Actual I-Level: K024-09-02-500
Part No.: 7718037
Hardware Index: 3
Coding Index: 9
Manufacturing Date(YY/MM/DD): 2004-04-15
MCV: 0.6.0
FSV: 2.2.1
OSV: 3.3.0
Manufacturer: Loewe Lear
HWOE No.: 25912776
 
Configuration 
   Speed sensor manufacturer is Bosch 
   Speed sensor type is DF11 
   ABS fitted 
   Heated grips 
   Heated seat driver 
   Heated seat passenger 
   Outside temperature sensor 
   Brake light switch status over CAN 
   Film type fuel sensor 
   Manual low beam off switch 
   Storage of temperature indication when engine hot 
   Electronic windscreen present 
   Cruise control present 




No fault codes found

--------------------------------------------------------------------------------
Integral ABS 2 - CANPart No.: 7711978
HW Version No.: C1
Coding Index: 0
Manufacturing Date: 2007-09-17
HWOE No.: 25700208
Manufacturer: Continental Teves
MCV: 0.6.0
FSV: 2.2.0
OSV: 3.3.0
Free programming slots: 1
Serial No.: 679H0035A
Hardware No.: 07682002
Hardware star No.: 07711978




No fault codes found

--------------------------------------------------------------------------------
CAN-Kombi H/LCluster type: CAN-Kombi H/L
Part No.: 7718209
Hardware Index: C6
Coding Index: 4
Manufacturer: Siemens VDO Automotive
Manufacturing Date: 2007-02-08
HWOE No.: 25913384
MCV: 0.6.0
FSV: 1.7.1
OSV: 3.3.10
Factory I-Level: K024-07-10-500
Actual I-Level: K024-09-02-500
Assembly No.: 07718210




1 fault codes found:

37641 Electrical System (KL30) under-voltage
The fault is not present now.
 

StephanT:
Rapala,

the GS-911 does not say that you do not have ESA... it says that you do not have an ESA with a HALL sensor, and thus cannot be calibrated...

there are 2 ways to measure the ESA position, the first units that were released, used a potentiometer to measure the position. The next versions (Still ESA 1) used a HALL sensor... And the ZFE configuration then has a bit that states whether your ESA is equipped with a Hall sensor.. hence "ESA with Hall sensor fitted"

If you can, what I would like would be posting some pictures of your ESA, especially the electrical connectors on the front and rear struts...

thanks
Stephan

rapala50:
No where on this Autoscan does it say I have ESA, or that I don't ESA with Hall sensor, here is a picture of my ESA switch, to much Tupperware to remove for a picture if the connectors, sorry....

Navigation

[0] Message Index

[#] Next page

[*] Previous page