General Category > General Discussion

Tyre Pressure TPMS / Wake-Up tool for RDC

<< < (15/17) > >>

Chetz86:
Hi Gunleif,

I also got an kingbolen EL50448 with GS911 but sadly i not able to wake the TPMS . Did this forum got any post that guide us to wake up the TPMS or u got any trick to make it success ?

Tan

e7navy1999:
Good Morning Chetz86.  Honestly I was unable to wake up my TPMS with the El50448 as well.  I do know that if you rapidly decompress the tire it wakes them up.  You have to rapidly deflate about 50% of the air.  BMW sort of messed up in this design.  I like to know my tire pressure before I ride two blocks down the road.  The GS911 will wake them as well.  I recently change the batteries in both front and rear.  It is a rather easy process once you get the glue broken out of the TPMS pocket.  There are many post or how to do the work.  If you can do your own tire changes and balancing the the cost of a TPMS battery repair is just about $1.  I think a new TMPS from BMW is $178 but I have seen them on Alibaba for $30 ish.  If you use the Alibaba TPMS then make certain you convert the hexadecimal code to real numbers.  There is a chart on google that will help.  If you change out your TPMS with a Chinese version or BMW with will still need a GS911 to input the new codes .  Beware many Chinese version sit for years on the shelf and the batteries may already be dead.  All this above is why I decided to just make my original TPMS where I can change the battery myself.  No programming, no worries.  Once you have them setup for battery replacement a new battery only takes 5 minutes per tire during a rubber change.  Good Luck

hefy_jefy:
Bike is 2014 R1200RTW - the EL-50448 worked just fine for me.  Turn on the ignition and select the tire pressure readout.  Hold the device exactly as shown in the instructions and press the button, the green LED flashes for about 5secs then the red LED gives a quick flash.  About 5secs later the pressure for whichever tire you are looking at shows up in the display.

My question is does anybody know exactly how these TMPS things work?  Is there a centrifugal switch that disconnects the battery?  If so how come they can be turned on by the EL-50448?

Is this tool (its only $10) really necessary?  If you know the 7 digit code of the sensor you are working with and have a GS911 can you just enter the code in the GS-911?

The only reason I purchased mine was because I want to change the battery in one of the sensors and I don't want to go to the trouble of changing the tire and THEN find it doesn't work!

Geoff

GS Jim:
Yes it is a centrifugal switch that turns on the sensor, how it gets turned on by the wake up tool I don't know, some electrical voodoo I guess, all I know is it works and that is good enough for me ;D It is to save the battery when not in use although I have a truck that the sensors are on all the time and it is 8 years old and still works fine, maybe those batteries are "truck" sized. The GS911 doesn't have voodoo so it won't  wake up the sensor, who knows maybe the next one will be GS911 wifivoodoo.  :o
The wake up tool also works on some vehicles for rotating tires and matching position also.

davtho1957:
When I first got my 2015 R1200 GSA, it was possible to program 2 sets of sensor ID's. Sometime during BMW service visits the ECU received an update and that is no longer the case. I have an Autel TS-401 TPMS tool. It allows me t read out the ID and wake the sensor up. During a brief tire/wheel change I noticed that the bike automatically recognized the other sensor on the wheel I had replaced (previously entered into system). It appears that if you change out one wheel, then ride 25 - 50 km, it will pick up the other previously used ID.

Navigation

[0] Message Index

[#] Next page

[*] Previous page

Go to full version