General Category > Engine related issues

knock sensor 2 defective

(1/2) > >>

ihosc:
Just purchased a GS911 and ran an autoscan on my 1200R. The report came up with a fault code "10210 knock sensor 2 defective. The fault is not present now." How would you recommend to go about working on this fault? Thanks in advance for the pointers.

StephanT:
pls post a Complete AUTOSCAN, as well as the Freeze frame data

best
Stephan

Haakon:
What Stephan ask for  :)

A bit too often the ECU (BMS- or whatever the bikes computer is named) store faults.
Faults that are not important. Reset the faults, start the bike and check once more.
The "Autoscan" show a lot more information, not the least when the the error popped up and for how long there WAS a fault.
 

ihosc:
Hi Stephan, Thanks for the respond. Below is the autoscan printout. I'm not sure if the freeze frame data is included. By the way I'm aware of my faulty tyre pressure sensor which I'm about to replace. It's only surprise me when I learned this knock sensor defective fault code. Wondering if I should replace them all at once. But before that just want to know if the sensor was really faulty or just data log error.. 

AutoScan Report
GS-911 version: 1310.1 Datapack version:1.7 Serial Number: GS60463402 Registered to: Seng Chuan Ho
Date: 17/12/2013 Time: 06:07:46

Motorcycle Information
VIN: WB10378009ZV59204
Mileage: 78299.0 km
Factory I-Level: K024-08-08-500
Actual I-Level: K024-11-08-510

BMS-KP2
BMS type:   BMS-KP2
Part No.:   7722565
Hardware Index:   10
Coding Index:   2
Manufacturing Date(YY/MM/DD):   2008-06-30
MCV:   0.6.0
FSV:   0.77.35
OSV:   2.3.1
Manufacturer:   Bosch
HWOE No.:   25928402
Program status:   350I
Date release:   7C10
Factory I-Level:   K024-08-08-500
Actual I-Level:   K024-11-08-510
VIN model year:   2009

1 fault codes found:

10210   Knock-sensor 2 defective
The fault is not present now.


ZFE-Basic
ZFE type:   ZFE-Basic
Factory I-Level:   K024-08-08-500
Actual I-Level:   K024-11-08-510
Part No.:   7720222
Hardware Index:   C7
Coding Index:   9
Manufacturing Date(YY/MM/DD):   2004-03-01
MCV:   0.6.0
FSV:   2.3.0
OSV:   3.3.0
Manufacturer:   Loewe Lear
HWOE No.:   25893770
Configuration   
   Speed sensor manufacturer is Bosch   
   Speed sensor type is DF11   
   ABS fitted   
   Outside temperature sensor   
   Brake light switch status over CAN   
   Rear bulb replacement   
   Film type fuel sensor   
   Manual low beam off switch   
   Storage of temperature indication when engine hot   

No fault codes found


Tyre pressure only
RDC/DWA type:   Tyre pressure only
Part No.:   7720818
Hardware Index:   C3
Coding Index:   4
Manufacturer:   Schrader
HWOE No.:   25946154
MCV:   0.6.0
FSV:   2.1.0
OSV:   4.0.2

2 fault codes found:

40471   Reception of front tyre-pressure sensor signal disrupted
The fault is currently present.
40465   Front tyre-pressure sensor faulty
The fault is currently present.


CAN-Kombi-K7
Cluster type:   CAN-Kombi-K7
Part No.:   7713995
Hardware Index:   C3
Coding Index:   1
Manufacturer:   Preh
Manufacturing Date(YY/MM/DD):   2008-07-07
MCV:   0.6.0
FSV:   2.2.0
OSV:   3.3.30
HWOE No.:   25745122
Assembly No.:   7714230
Factory I-Level:   K024-08-08-500
Actual I-Level:   K024-11-08-510

No fault codes found


Integral ABS 2 - CAN
Part No.:   7711978
HW Version No.:   C2
Coding Index:   0
Manufacturing Date:   2010-11-07
HWOE No.:   25695722
Manufacturer:   Continental Teves
MCV:   0.6.0
FSV:   2.2.0
OSV:   3.3.0
Free programming slots:   1
Serial No.:   6AB7002C4
Hardware No.:   07682002
Hardware star No.:   07711978

No fault codes found

StephanT:
thanks for this!

is it an R1200R ?

and can you do me a favour, and go into the BMSK and then read fault codes... this will show you the freeze frame data... I want to show you something on it

best
Stephan

Navigation

[0] Message Index

[#] Next page