Author Topic: What needs to connect to what for set up ?  (Read 18937 times)

Engie

  • Newbie
  • *
  • Posts: 5
  • Karma: +0/-0
What needs to connect to what for set up ?
« on: January 25, 2014, 08:57:11 PM »
I have a Windows 8.1 Tablet which would be neat to use with the USB connected enthusiast GS-911 but my tablet connects by WiFi (802.11b/g/n) to my wireless router in the house.  Our house is built of brick, cavity wall, two walls with an air gap and thermal insulating foam in the middle, which means that the WiFi signal is poor to non existent in the garage.

The following instruction indicates that for setup the Tablet must be connected to the internet :-
 
Quote
Run the GS-911downloader. The Downloader will instruct you when to connect your GS-911 interface to the PC (after it has installed the correct driver), after which it will connect to the server to determine which versions are available for download.  A browser window will be opened and list the GS-911 interface details and appropriate download links.


The following instruction indicates that for setup the Tablet must be connected to the motorcycle f800GT :-

Quote
Once installed, open the GS-911 software, and select Setup under Tools in the menu bar. Make sure you have USB selected and then click [Test interface]. This will test the interface, and report the firmware version, serial number, battery voltage of the motorcycle etc.

Does this mean that set up cannot take place in the garage if the GS-911 cannot be connected to the internet and bike at the same time ?

A previous post about being able to use different PCs with independently downloaded software indicates that the motorcycle ECU serial number gets burnt into GS-911 device (Enthusiast version - one of the ten) and the downloader ensures that a genuine/valid GS-911 is connected to the tablet before allowing the software to be activated (by connecting to the server).  This process indicates that set up could not take place without the GS-911 and tablet being connected to both the motorcycle and the internet.  On all 'Youtube' videos demonstrating setup, this is the case.

1)  Does this mean that set up cannot take place if the GS-911 cannot be connected to the internet and bike at the same time ?

2)  If it can then what is the sequence for doing it ?

I think that I am safe to assume that once set up the GS-911 and tablet are autonomous.
 


Engie

  • Newbie
  • *
  • Posts: 5
  • Karma: +0/-0
Re: What needs to connect to what for set up ?
« Reply #1 on: January 26, 2014, 12:06:08 AM »
Just thought of another question :-

Is the GS-911 powered from the bike connection or the USB cable ?

I assume it is powered from the bike because of the Bluetooth option, I therefore assume that it cannot operate away from the bike, starting to answer my own questions.

Snowy

  • Newbie
  • *
  • Posts: 5
  • Karma: +0/-0
Re: What needs to connect to what for set up ?
« Reply #2 on: January 26, 2014, 04:35:39 PM »
I have the PC version of the 911 so there's no bluetooth - therefore I can't be sure yours works in a similar fashion. In order to download the software to the PC I have to have the 911 connected to the PC and the internet. It does not connect to the bike at this time. To use the 911 on the bike I just have the PC and 911 with no internet access. I would have guessed that with the bluetooth version you can download software to the phone without being connected to the bike. When you use it for real on the bike you won't need the internet to read fault codes on the mobile. I think.......

Engie

  • Newbie
  • *
  • Posts: 5
  • Karma: +0/-0
Re: What needs to connect to what for set up ?
« Reply #3 on: January 26, 2014, 07:14:48 PM »
Thanks,    that means that if you can do this then the GS-911 hardware can be powered by the USB cable so that the PC can read a code from it and then via the internet compare it to a list of codes on a server at Hex.  I assume this is what it does, thereby identifying the hardware.

Perhaps I am wrong and it doesn't do this.  I am speculating from the instruction :-

 
Quote
after which it will connect to the server to determine which versions are available for download

Haakon

  • Full Member
  • ***
  • Posts: 145
  • Karma: +9/-1
Re: What needs to connect to what for set up ?
« Reply #4 on: January 27, 2014, 02:18:59 AM »
The GS911 are powered by a USB cable OR the bike- both.
How to download the sofware without a USB connection I do not know.

I think your question is easily answered? Hope it is!
The GS911 does NOT connect to the internet!! No WAY!
Just do as the instructions tell, make sure your tablet have a internet connection- wi-fi or whatever.
Follow the instructions and connect you GS911 to the tablet (via USB) when you are told to do so. 
Thats all. I think? 
 
2000 F650-GS

Engie

  • Newbie
  • *
  • Posts: 5
  • Karma: +0/-0
Re: What needs to connect to what for set up ?
« Reply #5 on: January 28, 2014, 11:54:31 AM »
Re :
Quote
The GS911 does NOT connect to the internet!! No WAY!

I realize the GS-911 connects to the tablet by USB cable with the tablet connected to the internet over Wi-Fi, (for software download and set up) but does the GS-911 have to be connected to the bike as well ?

Engie

  • Newbie
  • *
  • Posts: 5
  • Karma: +0/-0
Re: What needs to connect to what for set up ?
« Reply #6 on: January 28, 2014, 12:02:15 PM »
Snowy's response indicates that the answer is no, it does not have to connect to the bike for software download and set up. :) Thanks

Haakon

  • Full Member
  • ***
  • Posts: 145
  • Karma: +9/-1
Re: What needs to connect to what for set up ?
« Reply #7 on: January 29, 2014, 04:33:34 AM »
I am happy got it solved!  IF you did?
As so often, its all a matter of following instuctions.
And NOT think its more dificult than it is :D
2000 F650-GS