Author Topic: Using ezCan Hex Gen II with Admore lights and TT Denali D2 aux lights & aux horn  (Read 338 times)

motoUX

  • Newbie
  • *
  • Posts: 9
  • Karma: +0/-0
Hi all,

Here's what I would like to connect:
  • Left and right D2s into one ezCan Hex Gen II (EZC2) circuit]
  • Horn into another EZC2 circuit]
  • Admore brake lights into one EZC2 circuit]
  • Admore turn signals into one EZC2 circuit
for a total of four circuits. It seems that, for my Admore light strip to work for both brake/running and turn signals, it needs two separate circuits. I'm fine with my D2 lights being on or off (rather than being controlled separately).

Is this possible? Thanks in advance!
« Last Edit: April 22, 2021, 06:40:57 PM by motoUX »

StephanT

  • Administrator
  • Sr. Member
  • *****
  • Posts: 449
  • Karma: +21/-2
    • HEXcode
hi motoUX

not sure what the question is - you seem to have figured it out already...  ;D

What you should do is set one channel to

Set another to

and then the remaining two to and respectively

to connect the lights to one circuit a splitter comes in handy: https://www.hexinnovate.com/product/mt-3-pin-y-splitter-cable/


and you're good to go!  ....ez  ;D


consider supporting my fundraiser for the Heart Foundation:
https://www.justgiving.com/fundraising/stephan-hex
currently riding: BMW F850GS Adv - slightly modified

motoUX

  • Newbie
  • *
  • Posts: 9
  • Karma: +0/-0
hi motoUX

not sure what the question is - you seem to have figured it out already...  ;D
....

to connect the lights to one circuit a splitter comes in handy: https://www.hexinnovate.com/product/mt-3-pin-y-splitter-cable/


and you're good to go!  ....ez  ;D

Ah...might have to reattach the D2 connectors to I can use the splitter, I reckon (when the dealer installed the lights, they cut the Denali quick-connectors off in order to install the lights using posiconnectors on the EZHC)

motoUX

  • Newbie
  • *
  • Posts: 9
  • Karma: +0/-0
Aaaand....Y-cable is now ordered!

motoUX

  • Newbie
  • *
  • Posts: 9
  • Karma: +0/-0
Hooking the new unit up Wednesday...fingers crossed (or Daumen gedrückt, or whatever your symbol for "good luck" might be!).

motoUX

  • Newbie
  • *
  • Posts: 9
  • Karma: +0/-0
Received my new unit (thanks!). Now ready to install...and I still have a question ;)

If I use two circuits for the Admore lights (one left blinker and one right blinker), will i have
  • Running lights (at say 20% illumination)
  • Brake lights on activation
  • turn signals

I'm only asking because, on the Web site, it has this info:

There are multiple ways of connecting your Admore light to the ezCAN. To make full use of the features of the Admore light connect the wires and configure the ezCAN as follows:

ezCAN accessory output (white) to Admore Red (switched 12V source)
ezCAN brake output (yellow) to Admore Blue (brake input)
ezCAN accessory or brake ground (black) to Admore Black (ground)
Admore green and yellow (right/left turn signal inputs) can be tapped directly into the turn signal wires of the bike, as per the Admore instructions
Configure the ezCAN to use 2 channels with the yellow and white configured for brake and accessory respectively, remember to set the tail/rear light brightness to 0% and the brake light brightness to 100%. Set the ezCAN brake to “No flashing”.


I prefer NOT to tap into existing wiring via splicing into the bike's turn signal wiring.

Make sense?  Thanks!

motoUX

  • Newbie
  • *
  • Posts: 9
  • Karma: +0/-0
Totally didn't work. Back to square one.