Author Topic: R1100GS no start condition  (Read 448 times)

exopar

  • Beta testers
  • Newbie
  • *
  • Posts: 20
  • Karma: +0/-0
R1100GS no start condition
« on: November 20, 2019, 09:37:16 PM »
Dear friends

Have a R1100 GS withy no start condition.
The customer replaced the Hall sensor with no results.
Noticed injectors with constant (no pulse) current hence too much gas causing no start condition.

Also noticed higher than normal ground resistance between chassis and battery.

Need to find a wiring diagram for this model.
Also, would like to know if there is any way to jump wires from round GS911 diagnostic tool to 3 pin wire diagnostic port.
Any other clue where to look for a solution, in this case, would be highly appreciated.

Regards
Ray


WayneC

  • Beta testers
  • Hero Member
  • *
  • Posts: 1007
  • Karma: +18/-1
Re: R1100GS no start condition
« Reply #1 on: November 21, 2019, 02:22:59 AM »
You will find Hexcode have a 3 pin adaptor cable available for the old models, no need to "jump wires"

schuppi

  • Sr. Member
  • ****
  • Posts: 401
  • Karma: +13/-0
Re: R1100GS no start condition
« Reply #2 on: November 21, 2019, 11:04:07 AM »
Schönen Tag
Wolfgang
                                       talk less, drive more

exopar

  • Beta testers
  • Newbie
  • *
  • Posts: 20
  • Karma: +0/-0
Re: R1100GS no start condition
« Reply #3 on: February 05, 2020, 07:00:12 PM »
You will find Hexcode have a 3 pin adaptor cable available for the old models, no need to "jump wires"
I have been searching Hex Can web but have not found such adaptor, may someone be so kind to provide links to purchase this 3 pin adaptor?

Regards
Ray

WayneC

  • Beta testers
  • Hero Member
  • *
  • Posts: 1007
  • Karma: +18/-1
Re: R1100GS no start condition
« Reply #4 on: February 06, 2020, 02:17:06 AM »
Look down the list on this page, https://www.hexcode.co.za/products

You will find the adaptor

GS-911 3-Pin Interface, designed by HEX Code, has support for USB connectivity and is compatible with Windows™.

It is a complete stand alone GS-911 diagnostic tool (no other GS-911 device required) and is designed exclusively for the older models which have a flat three pin diagnostic connector. Applicable for Bosch Motronic versions MA2.1, MA2.2 as well as the ABS II controller. Please see the Function Chart.

NOTE: This device replaces the previous 3-pin adapter.

This product is available through our Distributors (see our reseller page), or directly from our online shop.
« Last Edit: February 06, 2020, 03:18:17 AM by WayneC »

exopar

  • Beta testers
  • Newbie
  • *
  • Posts: 20
  • Karma: +0/-0
Re: R1100GS no start condition
« Reply #5 on: February 06, 2020, 04:52:24 PM »
Yes Sr.

Been trying to place an order but no way to do it. May it be a discontinued product?
Any other third party vendor that may have it?

GS Jim

  • Full Member
  • ***
  • Posts: 147
  • Karma: +7/-0
Re: R1100GS no start condition
« Reply #6 on: February 06, 2020, 05:44:38 PM »
Look on the "Resellers" tab on the main page and find one in your country. Probably where you bought your GS911 originally?



exopar

  • Beta testers
  • Newbie
  • *
  • Posts: 20
  • Karma: +0/-0
Re: R1100GS no start condition
« Reply #7 on: February 06, 2020, 06:15:22 PM »
Thats the point

No distributor in Mexico so far.
Anyhow found a reseller in the USA able to ship to Mexico.
Thanks a lot for your advice.