General Category > ABS related issues
Servo ABS again!
Hunda67:
Hello,
New here but thought I'd ask the question in case someone can help :)
Bike is 2006 R1200GS Adventure with the Servo assisted ABS brakes.
2 months ago (after cleaning out the system and replacing a broken pressure switch) all working fine according to GS911 - during the tests all 4 circuits (front and rear control circuits and the front and rear wheel circuits) all showing between 17 and 20 bar of pressure during Sensor Drift Test. Also no faults in ABS fault history. Over next 2 months and 700 miles approx. no issues with the brakes at all.
On a recent trip "brake failure" warning came up on a quiet stretch of motorway. Stopped the bike switched ignition off and on and fault cleared. When I got home checked the faults with the GS911 and the following faults came up:
25165: Internal Control Module Error - main processor reset due to indervoltage
24951: ABS motor rear, defective
24971: Pressure in front wheel circuit to high
In all 3 cases the faults are no longer present. Also rear ABS motor is working fine (whizzing away) and battery is new.
However, front wheel circuit is showing a pressure of only 4 bar:
and because of this Sensor Drift test will not run:
I have bled and flushed the system through and there is no air in the system and the fluid is all clean. Can't see any leaks anywhere in the system and if I ride the bike all appears to function as normal (full strength brakes, no warning lights).
My questions are:
1. Why does bike (or the GS911) not give a constant error if the front wheel circuit pressure is low?
2. Is it likely to be another faulty pressure switch in the ABS Servo unit or could it be something else?
Or anyone have any orther ideas?
Thanks in advance.
mopedi:
Did you perform braking at a time when you received brake failure indicator on instrument cluster? The best would be if you have GS911 with you when brake failure is present to read active errors (in red color) otherwise after power off/on this errors becomes in black color and you do not know when it happened.
My real concern would be to a pressure sensor showing 4 bars at no brakes activated. This leads to failed or in near future failed pressure sensor. Existing original pressure sensors do fail without any announcement or predefined way! This sensors are not temperature compensated and would in healty status show ideally 20bar at 20degC, at 30degC the same sensor would show in range of 17bar and at 10degC it would show in range of 22bars. This pressure sensors are very sensitive and would most likely fail if you unscrew 5wing torx bolts from sensor support. Most often rear wheel pressure sensor would fail to value above 30bar because of higher braking fluid pressure at rear wheel at braking process, this leads to rear wheel pressure modulation.
The tricky part by purchasing used modulator with healty pressure sensors is that you do not know (and can not predict) how long pressure sensors will be ok.
Hunda67:
--- Quote from: mopedi on August 30, 2017, 01:21:51 PM ---Did you perform braking at a time when you received brake failure indicator on instrument cluster? The best would be if you have GS911 with you when brake failure is present to read active errors (in red color) otherwise after power off/on this errors becomes in black color and you do not know when it happened.
My real concern would be to a pressure sensor showing 4 bars at no brakes activated. This leads to failed or in near future failed pressure sensor. Existing original pressure sensors do fail without any announcement or predefined way! This sensors are not temperature compensated and would in healty status show ideally 20bar at 20degC, at 30degC the same sensor would show in range of 17bar and at 10degC it would show in range of 22bars. This pressure sensors are very sensitive and would most likely fail if you unscrew 5wing torx bolts from sensor support. Most often rear wheel pressure sensor would fail to value above 30bar because of higher braking fluid pressure at rear wheel at braking process, this leads to rear wheel pressure modulation.
The tricky part by purchasing used modulator with healty pressure sensors is that you do not know (and can not predict) how long pressure sensors will be ok.
--- End quote ---
I think that's it - I took sensors from a second hand unit and whilst working for a few weeks one must have since failed. Since first posting I have removed the servo system and am quite happy without abs/servos. I would put the servos and ABS back but only if I can source some new ones.
Sent from my SM-G920F using Tapatalk
mopedi:
I perform replacement of pressure sensors with custom made ones, temperature and aging compensated. The replacement requires new sensor holder, some machining on modulator body to accomodate new sealing o-ring. The solution I implemented on at least 40 servo modulators with 3 years of experience. The solution is similar to RH Electronics solution but for half a price.
Hunda67:
--- Quote from: mopedi on August 30, 2017, 02:00:11 PM ---I perform replacement of pressure sensors with custom made ones, temperature and aging compensated. The replacement requires new sensor holder, some machining on modulator body to accomodate new sealing o-ring. The solution I implemented on at least 40 servo modulators with 3 years of experience. The solution is similar to RH Electronics solution but for half a price.
--- End quote ---
That's interesting to know. So what is your cost for overhauling the sensors? Do you need the whole ABS unit or just the two plates with the pressure switches?
Sent from my SM-G920F using Tapatalk
Navigation
[0] Message Index
[#] Next page
Go to full version