GS-911 and ezCAN User Forum
General Category => GS-911 => Topic started by: Morrington on March 26, 2024, 02:37:01 PM
-
Hi,
Gs911 WiFi with Nov 2023 update on a 2021 S1000RR.
It turns out I have a fault code showing regarding my alarm system battery being empty. I've replaced the batteries and cleared all faults through the Auto scan so none show however I continue to have the big yellow empty alarm system battery fault showing on my dash after I switch the bike off and on again. No matter what I do I can't seem to clear it.
Does anyone know if the gs911 is capable of clearing this or is it a dealer only kind of thing.
Thanks.
-
Hi Morrington
Best would be to share an autoscan of your bike with the fault code present - download it as text and paste it in your response here.
Without any more info there really isn't much we can do to help unless someone has experienced this exact issue.
Kind regards
Ruan
-
Thanks for your reply.
I think that may be the problem. No fault is shown on the gs911 but the fault shows on the dash. It's as if the gs911 is not aware that there is a fault.
I'll do another autoscan later and see if anything changes.
-
Hi Morrington
That's strange, if the GS-911 doesn't recognise a fault that means it's something the ECU doesn't deem relevant to report as a fault, but I would suggest to scan the bike once the fault pops up, might be a different controller reporting it.
Kind regards
Ruan
-
on the earlier bike when replacing the batteries its very easy to dislodge the two silly plugs that get the power on to the PCB - to make it pretty inside they twist the wires around each other till they end up too short
-
The 2021 alarm unit batteries are in a secondary compartment so no requirement to unplug wires from the pcb. To be honest I was grateful about that as having watched the YouTube vids on the old module I wasn't keen on taking it to pieces.
-
Here's the autoscan copy. The fault code still appears on the dash "Alarm system battery empty. No independent alarm. Make an appointment at a specialist workshop". Perhaps this particular fault is not able to be read by the gs911? If so can I submit a suggestion that it be looked into?
Wi-Fi signal strength Battery voltage
13.1V
GS-911 | AutoScan (S1000RR)
ⓘ
AutoScan
Firmware Version 1.76 - 0.281
Data pack Version 256
Serial Number GS3 007 677
Registration ....
Date 2024-03-27 13:10:54
Bike Information
Odometer 5224.7 mi
Motorcycle Date 04-01-2016
Distance to next service 6214.0 mi
Service due date 06-12-2024
VIN
...
Model
S 1000 RR (K67) 2019
Factory I-Level
K001-21-07-500
Actual I-Level
K001-23-03-502
Vehicle Order +
Controller Summary
Engine Controller
OK
Tyre Pressure Monitor
OK
ABS Brakes
OK
Semi-active Suspension
OK
Immobilizer / Keyless Ride
OK
Anti-Theft Alarm
OK
Instrument Cluster
OK
Body Controller Lite
OK
Battery voltage
13.30 V
Engine Controller
(XBMSO1)
Controller Type Engine Controller
Controller Name XBMSO1
Controller 0x0F8B50
Serial Number 0170301964
Manufacturer Bosch GmbH
Manufacture Date (YY/MM/DD) 21/08/12
Program Count 20
Program Count Maximum 60
Battery voltage 13.30 V
VIN WB10E2109N6F05857
Model S 1000 RR (K67) 2019
Factory I-Level K001-21-07-500
Actual I-Level K001-23-03-502
Backup I-Level K001-22-03-504
Odometer 5224.7 mi
Operating hours 120h 15m 48s
Firmware Date (YY/MM/DD) 13/09/23
Kilometers when programmed 0.0
Number of FW configurations 5
HW Electronics (HWEL) +
Bootloader (BTLD) +
SW Memory Image (SWFL) +
Software creation level (SWFK) +
Coding Data (CAFD) +
Riding Mode 1
Fault Codes 0
No Faults found
Tyre Pressure Monitor
(XRDC)
Controller Type Tyre Pressure Monitor
Controller Name XRDC
Controller 0x0F8100
Serial Number 2292102629
Manufacturer Schrader
Manufacture Date (YY/MM/DD) 21/08/17
VIN 6F05857
Program Count 0
Program Count Maximum 1024
Firmware Date (YY/MM/DD) 99/99/99
Kilometers when programmed 0.0
Number of FW configurations 4
HW Electronics (HWEL) +
Bootloader (BTLD) +
SW Memory Image (SWFL) +
Coding Data (CAFD) +
Front Sensor Number 5393500
Rear Sensor Number 5399359
Fault Codes 0
No Faults found
ABS Brakes
(XABS)
Controller Type ABS Brakes
Controller Name XABS
Controller 0x0F8300
Serial Number 6079907261
Manufacturer AABG
Manufacture Date (YY/MM/DD) 21/08/19
VIN 6F05857
Variant Unknown
Program Count 1
Program Count Maximum 1000
Firmware Date (YY/MM/DD) 21/09/30
Kilometers when programmed 0.0
Number of FW configurations 4
HW Electronics (HWEL) +
Bootloader (BTLD) +
SW Memory Image (SWFL) +
Coding Data (CAFD) +
Fault Codes 0
No Faults found
Semi-active Suspension
(XSAF)
Controller Type Semi-active Suspension
Controller Name XSAF
Controller 0x0F8500
Serial Number 0000902810
Manufacturer Temic
Manufacture Date (YY/MM/DD) 21/08/19
VIN 6F05857
Program Count 1
Program Count Maximum 1024
Firmware Date (YY/MM/DD) 21/09/30
Kilometers when programmed 0.0
Number of FW configurations 5
HW Electronics (HWEL) +
Bootloader (BTLD) +
SW Memory Image (SWFL) +
SW Memory Image (SWFL) +
Coding Data (CAFD) +
Load setting Single
Damper setting Comfort
Fault Codes 0
No Faults found
Immobilizer / Keyless Ride
(XEWS4)
Controller Type Immobilizer / Keyless Ride
Controller Name XEWS4
Controller 0x0F8C00
Serial Number 0000004373
Manufacture Date (YY/MM/DD) 21/07/12
Program Count 0
Program Count Maximum 1024
Firmware Date (YY/MM/DD) 99/99/99
Kilometers when programmed 0.0
Number of FW configurations 3
HW Electronics (HWEL) +
Bootloader (BTLD) +
SW Memory Image (SWFL) +
Fault Codes 0
No Faults found
Anti-Theft Alarm
(XDWA)
Controller Type Anti-Theft Alarm
Controller Name XDWA
Controller 0x0F8700
Manufacturer META System S.P.A.
Manufacture Date (YY/MM/DD) 21/08/11
VIN 6F05857
Program Count 0
Program Count Maximum 1024
Firmware Date (YY/MM/DD) 21/08/11
Kilometers when programmed 0.0
Number of FW configurations 4
HW Electronics (HWEL) +
Bootloader (BTLD) +
SW Memory Image (SWFL) +
Coding Data (CAFD) +
Fault Codes 0
No Faults found
Instrument Cluster
(XKOMBIHI)
Controller Type Instrument Cluster
Controller Name XKOMBIHI
Controller 0x0F9080
Serial Number 0000069633
Manufacturer Bosch GmbH
Manufacture Date (YY/MM/DD) 21/07/26
Odometer 5224.7 mi
Program Count 3
Program Count Maximum 61440
Factory I-Level K001-21-07-500
Actual I-Level K001-23-03-502
VIN 6F05857
Firmware Date (YY/MM/DD) 23/04/12
Kilometers when programmed 0.0
Number of FW configurations 13
HW Electronics (HWEL) +
Hardware Type (HWAP) +
Bootloader (BTLD) +
SW Memory Image (SWFL) +
Flash loader Slave (FLSL) +
SW Memory Image (SWFL) +
SW Memory Image (SWFL) +
SW Memory Image (SWFL) +
SW Memory Image (SWFL) +
SW Memory Image (SWFL) +
SW Memory Image (SWFL) +
SW Memory Image (SWFL) +
Coding Data (CAFD) +
Fault Codes 0
No Faults found
Body Controller Lite
(XBCL)
Controller Type Body Controller Lite
Controller Name XBCL
Controller 0x0F8A10
Serial Number 3221743608
Manufacture Date (YY/MM/DD) 21/08/06
VIN 6F05857
Program Count 2
Program Count Maximum 1024
Firmware Date (YY/MM/DD) 22/07/27
Kilometers when programmed 0.0
Number of FW configurations 4
HW Electronics (HWEL) +
Bootloader (BTLD) +
SW Memory Image (SWFL) +
Coding Data (CAFD) +
Fault Codes 0
No Faults found
Print
Download this data
Download this data HTML formatted
Registered:....
GS3 007677
Infrastructure
-
Hello
Just to clarify:
I don't think the integrated battery in the alarm system is monitored by the diagnostics.
This is what the instrument cluster shows: DWA!
Possible cause:
The integral battery in the antitheft alarm has lost its entire original capacity. There is no assurance
that the anti-theft alarm will be operational if the vehicle's battery is disconnected.
Did you ckeck the two new CR123A Lithium batteries and their connections?
-
Hi,
It's the gen 4 model so it shows a different fault on the dash but I'm sure it's essentially the same thing. I replaced the batteries with fresh ones but perhaps I've not seated them right. I'll open it back up and take another look and make sure they're not faulty with a multimeter.
I hadn't considered that the fault wouldn't show on diagnostics but that would explain why the gs911 wouldn't see it. I'll let you know how I get on.
-
After further digging,
The original batteries I removed still showed over 3V and a check of the contacts in the alarm module showed a break between the bridge of the 2 batteries. It looks like back to the dealer for a faulty alarm module, perhaps a replacement. Thanks for everyone's help. :)