No Speedo

[Junk]

I have a 2005 K1200S and here is the scan any help would be great! I had to replace the sensor that goes to the front wheel the wire was broke. I am new to all the been a Harley guy. I also don't have abs but I don't need them as bad as the speedo.
AutoScan Report
GS-911 version: 1401.2 Datapack version:1.8 Serial Number: GS60496402 Registered to: Brian Norwood
Date: 3/21/2014 Time: 6:30:33 PM

Motorcycle Information

 
VIN: WB10591A35ZM26620
Mileage: 44464.0 km
Factory I-Level: K024-05-02-510
Actual I-Level: K024-10-02-500

BMS-K
BMS type: BMS-K
Part No.: 7712714
Hardware Index: 10
Coding Index: 1
Manufacturing Date(YY/MM/DD): 2005-02-17
MCV: 0.5.8
FSV: 0.77.24
OSV: 2.3.1
Manufacturer: Bosch
HWOE No.: 25749908
Program status: 240E
Date release: AD12
Factory I-Level: K024-05-02-510
Actual I-Level: K024-10-02-500
VIN model year: 2005




1 fault codes found:

10219 CAN-bus Timeout: no communication with ZFE (Central Vehicle Electronics) control unit
The fault is currently present.
 

ZFE-High
ZFE type: ZFE-High
Factory I-Level: K024-05-02-510
Actual I-Level: K024-10-02-500
Part No.: 7699829
Hardware Index: C6
Coding Index: 7
Manufacturing Date(YY/MM/DD): 2004-04-15
MCV: 0.5.8
FSV: 1.10.3
OSV: 3.3.0
Manufacturer: Loewe Lear
HWOE No.: 26124076
 
Configuration 
   Speed sensor manufacturer is Beru 
   Speed sensor type is DF11 
   ABS fitted 
   Heated grips 
   Rear bulb replacement 
   Film type fuel sensor 
   Manual low beam off switch 
   Storage of temperature indication when engine hot 
   License plate bulb 



No fault codes found

CAN-Kombi H/L
Cluster type: CAN-Kombi H/L
Part No.: 7692307
Hardware Index: 1
Coding Index: 3
Manufacturer: Siemens VDO Automotive
Manufacturing Date(YY/MM/DD): 2003-07-24
MCV: 0.5.6
FSV: 1.5.4
OSV: 3.3.10
HWOE No.: 26113116
Assembly No.: 7692316
Variant: Unknown
Factory I-Level: K024-05-02-510
Actual I-Level: K024-10-02-500




2 fault codes found:

37649 CAN-bus timeout : No communication with ABS control unit
The fault is currently present.
37650 CAN-bus error: faulty speed signal
The fault is currently present.
 

[kobus]

Hi Brian

Your speedo won't work until the ABS is sorted out. The ABS sends the speed signal on the CAN bus so it can be used by cluster for display purposes.
In short, no ABS, no speed signal.

[Haakon]

Ahhh.... at first I read this and believed you did not HAVE a ABS system.
(I do NOT know the specifics re this bike- if it had ABS as an option)
Kobus is totally right.
Check all plugs, wiring and connections!
---------------
This error came after you fitted a new ABS sensor?
If so, start there- Make sure you have the right sensor to sensor wheen distance.
What else did you do prior to the sensor replacement?

[Junk]

When I got the bike the abs light was on no speedo and for some reason the blinker switch don't work. I seen the wire going to the front tire was broke the guy I got the bike said this happened when he was putting brake pads on the front. He said that was the reason for the problems. So I got a scanner and a sensor to try and find what all gremlins the bike has I think I need a big cow bell tied to the bike to chance all them away! When using the scanner I can make the blinkers blink put don't get a input back from the switches. I am going to take all the fairings off this weekend and unplug all the plunges and spray some cleaner on them. I really appreciate all the help! 20 years on Harley's and never ran into a brick wall like I feel when working in this bike.