General Category > GS-911 Wifi

Not sure what these error codes mean: wheel circumference faulty and gear select

(1/4) > >>

ddoggycanada:
Hi Everyone,
I've hooked up my bike to the GS911 and got these error codes... but I;m not sure what they mean and what the implications are!
the errors seem pretty frequent, should I be worried?

the 3 error codes are:

XABS : -
Controller Type : ABS Brakes
Controller Name : XABS
Controller : 0F8300
Serial Number : 6307500881
Manufacturer : Unknown
Manufacture Date (YY/MM/DD) : 16/02/05
VIN : Invalid
Variant : K50 + Hillstart + ABS-Pro
Program Count : 1
Program Count Maximum : 1000
Firmware Date (YY/MM/DD) : 19/04/05
Kilometers when programmed : 0.00
Number of FW configurations : 3
..HW Electronics (HWEL) :
....Firmware ID : 1299
....Firmware Version : 000.003.000
..Bootloader (BTLD) :
....Firmware ID : 1298
....Firmware Version : 000.002.000
..SW Memory Image (SWFL) :
....Firmware ID : 129A
....Firmware Version : 004.000.001
Fault Codes : 1
|
4809F0 : Wheel circumference is faulty
Currently present : NO
Engine warning light (MIL) : NO
Frequency count : 3
Logistic(Healing) count : 40
..Fault Code History :
....Record number : 0
....Odometer : 12395.0 km
....ABS time : 766094
....Status Control Unit : t-1188
....Sub Table : 16
....Battery Voltage : 14.65 V
....REF Speed : 25.0 km/h
....Brake Status : 0
....Sub Table : 208
....Internal Error ID : 0
....Record number : 1
....Odometer : 12409.0 km
....ABS time : 939871
....Status Control Unit : t-1188
....Sub Table : 32
....Battery Voltage : 14.17 V
....REF Speed : 59.0 km/h
....Brake Status : 0
....Sub Table : 208
....Internal Error ID : 0



XBMSX : -
Controller Type : Engine Controller
Controller Name : XBMSX
Controller : 0F8B00
Serial Number : 0170265195
Manufacture Date (YY/MM/DD) : 16/01/26
Program Count : 2
Program Count Maximum : 60
Factory I-Level : K001-15-07-522
Actual I-Level : K001-19-03-501
VIN : WB10A040XGZ279791
Odometer : 12422.0 km
Operating hours : 306h 48m 29s
Firmware Date (YY/MM/DD) : 19/04/05
Kilometers when programmed : 0.00
Number of FW configurations : 5
..HW Electronics (HWEL) :
....Firmware ID : 08A3
....Firmware Version : 004.000.000
..Bootloader (BTLD) :
....Firmware ID : 0C49
....Firmware Version : 004.000.000
..SW Memory Image (SWFL) :
....Firmware ID : 0CF7
....Firmware Version : 026.000.000
..SW Memory Image (SWFL) :
....Firmware ID : 1FB0
....Firmware Version : 026.000.000
..Coding Data (CAFD) :
....Firmware ID : 08A2
....Firmware Version : 000.008.009
Fault Codes : 1
|
21F662 : Gear selector sensor, implausible signal or value
Currently present : NO
Engine warning light (MIL) : NO
Frequency count : 1
Logistic(Healing) count : 40
..Fault Code History :
....Record number : 1
....Odometer : 12416.0 km
....ABS time : 940833
....Gear position sensor voltage : 3.86 V
....Engine speed : 3199.5 rpm
....Vehicle speed : 84.8 km/h
....Throttle valve angle relative to throttle valve stop : 19.53 %


XSAF : -
Controller Type : Semi-active suspension
Controller Name : XSAF
Controller : 0F8500
Serial Number : 0000279433
Manufacturer : Temic
Manufacture Date (YY/MM/DD) : 16/01/25
VIN : Z279791
Program Count : 9
Program Count Maximum : 1024
Firmware Date (YY/MM/DD) : 23/06/03
Kilometers when programmed : 0.00
Number of FW configurations : 5
..HW Electronics (HWEL) :
....Firmware ID : 1014
....Firmware Version : 001.000.001
..Bootloader (BTLD) :
....Firmware ID : 1013
....Firmware Version : 001.001.002
..SW Memory Image (SWFL) :
....Firmware ID : 1015
....Firmware Version : 007.010.001
..SW Memory Image (SWFL) :
....Firmware ID : 117D
....Firmware Version : 007.010.001
..Coding Data (CAFD) :
....Firmware ID : 1016
....Firmware Version : 007.004.009
Fault Codes : 1
|
D754A3 : CAN message timeout (Advanced mode from DME)
Currently present : YES
Engine warning light (MIL) : NO
Frequency count : 11
Logistic(Healing) count : 40
..Fault Code History :
....Record number : 1
....Odometer : 12394.0 km
....ABS time : 761374
....Record number : 2
....Odometer : 12422.0 km
....ABS time : 1043875

Any help would be greatly appreciated

GS Jim:
As this is your first post can we assume that this is a first scan?
Have you had the bike since new or bought used?
Also you should include the model/year etc of the bike.
Is the dash showing any warnings at all, if not record the scan and clear the faults and see if they come back.
What size/brand/model of tires are you using?
Check the encoder rings and sensors on both wheels for any issues.
If the transmission fault comes back do a gear calibration (don't remember the exact term in the GS911 diagnostics page).

Jughead:
The wheel circumference error will sometimes come up when new tyres are fitted.  Traction control is looking for a particular circumference which is adapted automatically as the tyres wear.  When new tyres are fitted, the circumference is suddenly different, so it brings up the error.  You just need to reset the adaptions and it will learn from there again.

Ditto the Gear Position Indicator.  Just reset the adaptions, put the bike on the centerstand and run through the gears.  About 5 secs in each gear is all that is required to read the new values.

ddoggycanada:

--- Quote from: GS Jim on June 11, 2023, 07:40:16 PM ---As this is your first post can we assume that this is a first scan?
Have you had the bike since new or bought used?
Also you should include the model/year etc of the bike.
Is the dash showing any warnings at all, if not record the scan and clear the faults and see if they come back.
What size/brand/model of tires are you using?
Check the encoder rings and sensors on both wheels for any issues.
If the transmission fault comes back do a gear calibration (don't remember the exact term in the GS911 diagnostics page).

--- End quote ---

Hi, yes I'm sorry,
this was my first scan, though other people have been clearing codes and doing stuff with my bike beforehand.
The model is 2016 BMW R1200R LC, and it was bought since new.
 The dash is not showing any warnings /
I've fitted the new R1250R TFT screen using a dongle that lets you connect the 7 pin instrument panel connector to the TFT's 12? pin connector.
With some tweaking using ESYS and ISTA, I was able to make it so that it works (at least on the surface level) on the R1200R.
The only problem being that when the dealer recorded the potentiometer the switching between the Dynamic / Road settings on the Dynamic ESA was receiving too little voltage, and that it may be flickering on and off, causing
So I naturally assumed it was some sort of a voltage issue because of this retrofit...

The tyres are Michellin Road 5, stock size.


I've only used the WIFI version with the GS911 App , is the "resetting adaptions" only available with the PC version?

Thank you so much both GS JIM and Jughead for your reply.

GS Jim:
These bikes are sensitive to things like the adding of the TFT and could possibly cause some issues like fault codes. Just clear all the faults and see what happens.
I've had the 5 Trails and now the Road 6 and many other brands of tires from new to the wear bars and never a fault, again, just clear the faults.
As Jughead says do the adaptations. There are several including suspension, transmission etc, go through all the sub menus on the GS911 PC Diagnostics app to find them, check first that the GS911 and app are up to date.

Navigation

[0] Message Index

[#] Next page